In the Mecca of Swiss Machining

The Swiss just voted overwhelmingly to bar the building of new minarets in Switzerland. No big deal in and of itself (only four of the country’s 150 mosques have them), but quite significant as a symbol of the discomfort level in the county over the “Islamification” of Europe. Minarets are tower-like structures built on top of mosques that are traditionally used for the call to prayer. None are used for that Switzerland however, because of strict noise pollution rules.

Muslims now comprise roughly five percent of the population of Switzerland, traditionally a conservative and insulated country. They have a much bigger presence in England, France and Holland.
If you visit the Haute-Savoie region of France, which borders Geneva, the machining hub of the region since clock making from wood was developed in the Jura Mountains, you will see thousands of satellite dishes aimed at Aljazeera transmitting towers. Arabia has been transplanted in Rolex-land. With the European machining community flattened by the recession a backlash at Muslims is not surprising.

Maybe it is a stretch, but I am going to connect the dots between the sudden resignation from CNN by the outspoken critic of Latino immigration, Lou Dobbs, and the vote in Switzerland. The rumor is that Dobbs wants to run against Robert Menendez of New Jersey, the only Latino in the U.S. Senate.

Is there a parallel between Islamic immigration to Europe and Latino immigration to the United States? Will Lou Dobbs ride an anti-minaret like backlash into the mainstream of American politics?

Question: If you discovered your best employee was an illegal, what would you do?

Minaret of Zurich’s Mahmud Mosque, 23 May 2007/Christian Hartmann

Minaret of Zurich’s Mahmud Mosque, 23 May 2007/Christian Hartmann

7 responses to “In the Mecca of Swiss Machining”

  1. I think if someone is willing to lie to get a job they’re either desperate or are willing to lie too easily. For someone to be the “best” employee they would probably not be the type of person who lies easily. There’s a fine line between doing what’s right, meaning showing compassion, and doing what’s right in terms of the law, sending them back home. I would keep them.

  2. As far as the best employee went, I would have to take 10 minutes or so to try and evaluate what would NOT go well in the shop if he could no longer work there. Then,I would contact an attorney t see what could be done about MAKING him a legal resident, then I wouldn’t hae to worry about losing him (except, possibly to an offer of a higher-paying job).

  3. Lloyd,

    I think that you are mischarecterizng Dobbs as being “anti Latino immigration” he is only on the record as opposing illegal imigration and is for securing the borders. It has been reported that he was forced out at CNN, with CNN paying out his contract and letting him “resign”.

    As far as what I would do if I found my best employee was an illegal alien the answer is pretty simple. If I continue to employ him or her, then I’m breaking the law so they would have to go. Depending on the circumstance I might try to get him/her legal help to try and make their status legal. But when you get right down to it, the relationship started with the employee fraudulently representing themself and that alone ought to be reason enough to terminate them.

    In any case, the soft bigotry of low expectations that Europeans have toward legal Muslim immigrants is apples and oranges when compared to the illegal immigration and porous border issue here.

  4. I would gather that some shop owners feel that an illegal that he can pay half wages to is the best employee.

  5. Not very well educated,but…….wasn’t Spain occupied by Muslims, without problems? Italy had
    strong Muslim influence, I think painting of perspective was “invented” by a Muslim in Florence.
    What I am saying is that historically I do not remember any real problems with these “Beleviers”.
    Only heard of “Christians” persecuting beliefs. Mr. G.W. should never have used the word
    “Crusade” he was ill advised. I am a Christian without a spell check, so please forgive spelling
    Just want to “stir the pot”

  6. You would have to try everything to make him legal!

  7. REPORT HIM, TIE HIM UP UNTIL THE IMMIGRATION GOT THERE, AND THEN FIRE HIS ASS !!!!!!!!!!!!!!!!!!!!!

Leave a Reply

Maier

Classifieds

Hilco Auction Sept. 27 Hydromat Boston Centerless Alliance Medvec Resources Group Trusty Cook Etco Partmaker Machine Tools

From the Experts

Mark Bos

Making parts faster doesn’t always mean cheaper
Mark Bos

By Mark Bos In today’s difficult economy, we are all trying to make parts faster and cheaper. Unfortunately, making parts faster is sometimes at odds with making them cheaper. I [...]

Dave Johnson

Shop Doc – Should I rebuild my Acme?
Dave Johnson

Dear Shop Doc, My Acme-Gridley screw machines have been real money makers over the years, but all that production takes its toll in wear and tear on the machines. Will [...]

dcogswell

Shop Doc – Bent Logo
David Cogswell

Todays’ Machining World Archives March 2008 Volume 04 Issue 03 Dear Shop Doc, We are trying to stamp our company logo on components produced on our CNC Swiss type machines. [...]

dmurphy

Shop Doc – Custom Macro programming
Dan Murphy

Today’s Machining World Archives August 2010 Volume 06 Issue 06 Dear Shop Doc, One of our operators came from another shop and told us that we can use Custom Macro [...]

Flavio Rovertoni

Shop Doc – When to go Hydromat
Flavio Rovertoni

Dear Shop Doc, We are a new job shop looking to add some equipment. We are wondering whether we should invest in used rotary transfer machines like a Hydromat Legacy [...]

jesse

Shop Doc – Justifying Use of a High-Speed-Spindle
Jesse Xi Chen

Dear Shop Doc, We have often heard the high speed machine spindle is expensive and has to be replaced at some point. Can you shed some light on the high [...]

pbagswell

Shop Doc – Micro Beginnings
Peter Bagwell

Dear Shop Doc, I have recently been asked if my shop does “micro” machining. I’ve done some work on small parts recently, but I’m not exactly sure what is meant [...]