Comments for Todays Machining World http://www.todaysmachiningworld.com The Magazine for the Precision Parts Industry Tue, 07 Feb 2012 07:06:57 +0000 hourly 1 http://wordpress.org/?v=3.2.1 Comment on How It Works – What happened? by payam ghasemihttp://www.todaysmachiningworld.com/how-it-works-what-happened/comment-page-1/#comment-12139 payam ghasemi Tue, 07 Feb 2012 07:06:57 +0000 http://www.todaysmachiningworld.com/?p=2898#comment-12139 hello Iam student ms ferdosi university of mashhad in iran.and my thesis is in the feild of turbin failure .and you have to interns and contents of the turbin failure . thanks. hello
Iam student ms ferdosi university of mashhad in iran.and my thesis is in the feild of turbin failure .and you have to interns and contents of the turbin failure .
thanks.

]]> Comment on Ethics: Drug Testing in the Workplace by Bigfoothttp://www.todaysmachiningworld.com/ethics-drug-testing-in-the-workplace/comment-page-1/#comment-12135 Bigfoot Fri, 03 Feb 2012 06:00:50 +0000 http://www.todaysmachiningworld.com/?p=10209#comment-12135 As an employer, I was concerned with the safety, productivity, and attitude of my machinists. Not how they spent their personal time. As an employee, I vehemently objected to being accused or suspected of using drugs. There was never a question of passing the test. My concerns were having to 'prove' over and over that I did not use drugs. I am not talking about 'for cause', or as pre-employment tests. As an employer, I was concerned with the safety, productivity, and attitude of my machinists. Not how they spent their personal time. As an employee, I vehemently objected to being accused or suspected of using drugs. There was never a question of passing the test. My concerns were having to ‘prove’ over and over that I did not use drugs. I am not talking about ‘for cause’, or as pre-employment tests.

]]> Comment on Problems Turning Tiny Parts on CNC Swiss by Roger Nicholashttp://www.todaysmachiningworld.com/new-shop-doc-cnc-swiss/comment-page-1/#comment-12134 Roger Nicholas Fri, 03 Feb 2012 00:24:10 +0000 http://www.todaysmachiningworld.com/?p=12469#comment-12134 Centerline is also important when using carbide tooling. If the tool is below center it is cutting material that has rotational forces pulling away from the surface of the carbide. As carbide is strong in compression it is weak in tension and the below center condition tends to pull away micro chips on the cutting edge surface reducing tool life. On center to a couple of thou. above center will keep the carbide in compression that can improve tool life. Roger Centerline is also important when using carbide tooling. If the tool is below center it is cutting material that has rotational forces pulling away from the surface of the carbide. As carbide is strong in compression it is weak in tension and the below center condition tends to pull away micro chips on the cutting edge surface reducing tool life. On center to a couple of thou. above center will keep the carbide in compression that can improve tool life.

Roger

]]> Comment on Problems Turning Tiny Parts on CNC Swiss by Roger Nicholashttp://www.todaysmachiningworld.com/new-shop-doc-cnc-swiss/comment-page-1/#comment-12133 Roger Nicholas Fri, 03 Feb 2012 00:23:05 +0000 http://www.todaysmachiningworld.com/?p=12469#comment-12133 Centerline is also important when using carbide tooling. If the tool is below center it is cutting material that has rotational forces pulling away from the surface of the carbide. As carbide is strong in compression it is weak in tension and the below center condition tends to pull away micro chips on the cutting edge surface reducing tool life. On center to a couple of thou. above center will keep the carbide in compression that can improve tool life. Most pressed carbide inserts have a height tolerence of -/+.005 so centerline may very from lot to lot of inserts. - another thing to keep an eye on. Roger Centerline is also important when using carbide tooling. If the tool is below center it is cutting material that has rotational forces pulling away from the surface of the carbide. As carbide is strong in compression it is weak in tension and the below center condition tends to pull away micro chips on the cutting edge surface reducing tool life. On center to a couple of thou. above center will keep the carbide in compression that can improve tool life. Most pressed carbide inserts have a height tolerence of -/+.005 so centerline may very from lot to lot of inserts. – another thing to keep an eye on.

Roger

]]> Comment on Problems Turning Tiny Parts on CNC Swiss by Wagshttp://www.todaysmachiningworld.com/new-shop-doc-cnc-swiss/comment-page-1/#comment-12131 Wags Thu, 02 Feb 2012 21:13:26 +0000 http://www.todaysmachiningworld.com/?p=12469#comment-12131 Definitely commercials. The only program on television where viewers actually pay attention to the ads. And who cares who wins unless your favorite team is playing?? Definitely commercials. The only program on television where viewers actually pay attention to the ads. And who cares who wins unless your favorite team is playing??

]]> Comment on Problems Turning Tiny Parts on CNC Swiss by Andy Collazzohttp://www.todaysmachiningworld.com/new-shop-doc-cnc-swiss/comment-page-1/#comment-12130 Andy Collazzo Thu, 02 Feb 2012 18:44:37 +0000 http://www.todaysmachiningworld.com/?p=12469#comment-12130 This same effect is also noticed when milling, interpolating a circle using polar coordinate mode, and a live axial tool. In this case you will end up with an oval. This same effect is also noticed when milling, interpolating a circle using polar coordinate mode, and a live axial tool. In this case you will end up with an oval.

]]> Comment on Problems Turning Tiny Parts on CNC Swiss by Diane Habererhttp://www.todaysmachiningworld.com/new-shop-doc-cnc-swiss/comment-page-1/#comment-12129 Diane Haberer Thu, 02 Feb 2012 18:07:35 +0000 http://www.todaysmachiningworld.com/?p=12469#comment-12129 definitely the commercials. I actually record the game so that I can go back and watch the commercials. I fast forward though the game and watch the commercials. definitely the commercials. I actually record the game so that I can go back and watch the commercials. I fast forward though the game and watch the commercials.

]]> Comment on Japan Earthquake — Response from Mitsui Seiki by Jayaraman.Khttp://www.todaysmachiningworld.com/japan-earthquake-response-from-mitsui-seiki/comment-page-1/#comment-12128 Jayaraman.K Thu, 02 Feb 2012 12:29:16 +0000 http://www.todaysmachiningworld.com/?p=9138#comment-12128 Mitsui Seiki is geat in quality,service,hospitality etc. But service to old customers is poor.That was the reason, TVS group have gone for Japanese make except Mitsui Seiki. Mitsui Seiki is geat in quality,service,hospitality etc. But service to old customers is poor.That was the reason, TVS group have gone for Japanese make except Mitsui Seiki.

]]> Comment on Manufacturing in Thailand – the “Detroit of the East” by Jimhttp://www.todaysmachiningworld.com/a-tour-of-manufacturing-in-thailand-%e2%80%93-the-%e2%80%9cdetroit-of-the-east%e2%80%9d/comment-page-1/#comment-12127 Jim Wed, 01 Feb 2012 18:44:48 +0000 http://www.todaysmachiningworld.com/?p=12393#comment-12127 I hope for the sake of Thailand, that there city is nothing like Detroit, thousands of homes decaying and even the Chief of Police in Detroit has said that he will not allow his troopers to into these neighborhoods and go into the homes, too dangerous! To be sure, Detroit area is no area that I would want to bring my business or customers to, if Thailand is trying to be anything like Detroit, I would never consider Thailand. I hope for the sake of Thailand, that there city is nothing like Detroit, thousands of homes decaying and even the Chief of Police in Detroit has said that he will not allow his troopers to into these neighborhoods and go into the homes, too dangerous! To be sure, Detroit area is no area that I would want to bring my business or customers to, if Thailand is trying to be anything like Detroit, I would never consider Thailand.

]]> Comment on Manufacturing in Thailand – the “Detroit of the East” by Bruce Renwickhttp://www.todaysmachiningworld.com/a-tour-of-manufacturing-in-thailand-%e2%80%93-the-%e2%80%9cdetroit-of-the-east%e2%80%9d/comment-page-1/#comment-12126 Bruce Renwick Wed, 01 Feb 2012 15:18:02 +0000 http://www.todaysmachiningworld.com/?p=12393#comment-12126 It is an enlightening and interesting article and I would assume great trip. I know when I was in Mexico I talked with people about the trousers that were made in the local factorys and saw how it improved the lives of the villagers in these areas. It's sometimes hard for me to wrap my mind aroud a global economy. I still say America can and will compete quite well. It is an enlightening and interesting article and I would assume great trip. I know when I was in Mexico I talked with people about the trousers that were made in the local factorys and saw how it improved the lives of the villagers in these areas. It’s sometimes hard for me to wrap my mind aroud a global economy. I still say America can and will compete quite well.

]]>